93 lines
2.4 KiB
Arduino
93 lines
2.4 KiB
Arduino
|
// demo: Use RX0BF and RX1BF as digital outputs
|
|||
|
|
// adlerweb, 2017-06-24
|
|||
|
|
#include <SPI.h>
|
|||
|
|
#include "mcp2515_can.h"
|
|||
|
|
#include "mcp2518fd_can.h"
|
|||
|
|
|
|||
|
|
#define CAN_2515
|
|||
|
|
// #define CAN_2518FD
|
|||
|
|
|
|||
|
|
// the cs pin of the version after v1.1 is default to D9
|
|||
|
|
// v0.9b and v1.0 is default D10
|
|||
|
|
|
|||
|
|
// Set SPI CS Pin according to your hardware
|
|||
|
|
// For Wio Terminal w/ MCP2518FD RPi Hat：
|
|||
|
|
// Channel 0 SPI_CS Pin: BCM 8
|
|||
|
|
// Channel 1 SPI_CS Pin: BCM 7
|
|||
|
|
// Interupt Pin: BCM25
|
|||
|
|
// *****************************************
|
|||
|
|
// For Arduino MCP2515 Hat:
|
|||
|
|
// SPI_CS Pin: D9
|
|||
|
|
|
|||
|
|
#define SPI_CS_PIN 9
|
|||
|
|
|
|||
|
|
#ifdef CAN_2518FD
|
|||
|
|
mcp2518fd CAN(SPI_CS_PIN); // Set CS pin
|
|||
|
|
#endif
|
|||
|
|
|
|||
|
|
#ifdef CAN_2515
|
|||
|
|
mcp2515_can CAN(SPI_CS_PIN); // Set CS pin
|
|||
|
|
#endif
|
|||
|
|
|
|||
|
|
|
|||
|
|
void setup() {
|
|||
|
|
SERIAL_PORT_MONITOR.begin(115200);
|
|||
|
|
|
|||
|
|
#ifdef CAN_2518FD
|
|||
|
|
while (0 != CAN.begin((byte)CAN_500K_1M)) { // init can bus : baudrate = 500k
|
|||
|
|
#endif
|
|||
|
|
#ifdef CAN_2515
|
|||
|
|
while (CAN_OK != CAN.begin(CAN_500KBPS)) {
|
|||
|
|
#endif // init can bus : baudrate = 500k
|
|||
|
|
SERIAL_PORT_MONITOR.println("CAN init failed, retry");
|
|||
|
|
delay(100);
|
|||
|
|
}
|
|||
|
|
SERIAL_PORT_MONITOR.println("CAN init ok");
|
|||
|
|
|
|||
|
|
#ifdef CAN_2518FD
|
|||
|
|
if (CAN.mcpPinMode(GPIO_PIN_0, GPIO_MODE_INT)) {
|
|||
|
|
#else
|
|||
|
|
if (CAN.mcpPinMode(MCP_TX2RTS, MCP_PIN_IN)) {
|
|||
|
|
#endif
|
|||
|
|
SERIAL_PORT_MONITOR.println("RX0BF is now an output");
|
|||
|
|
} else {
|
|||
|
|
SERIAL_PORT_MONITOR.println("Could not switch RX0BF");
|
|||
|
|
}
|
|||
|
|
|
|||
|
|
#ifdef CAN_2518FD
|
|||
|
|
if (CAN.mcpPinMode(GPIO_PIN_1, GPIO_MODE_INT)) {
|
|||
|
|
#else
|
|||
|
|
if (CAN.mcpPinMode(MCP_TX2RTS, MCP_PIN_IN)) {
|
|||
|
|
#endif
|
|||
|
|
SERIAL_PORT_MONITOR.println("RX1BF is now an output");
|
|||
|
|
} else {
|
|||
|
|
SERIAL_PORT_MONITOR.println("Could not switch RX1BF");
|
|||
|
|
}
|
|||
|
|
}
|
|||
|
|
|
|||
|
|
void loop() {
|
|||
|
|
SERIAL_PORT_MONITOR.println("10");
|
|||
|
|
#ifdef CAN_2518FD
|
|||
|
|
CAN.mcpDigitalWrite(GPIO_PIN_0, GPIO_HIGH);
|
|||
|
|
CAN.mcpDigitalWrite(GPIO_PIN_1, GPIO_LOW);
|
|||
|
|
#else
|
|||
|
|
CAN.mcpDigitalWrite(MCP_RX0BF, HIGH);
|
|||
|
|
CAN.mcpDigitalWrite(MCP_RX1BF, LOW);
|
|||
|
|
#endif
|
|||
|
|
|
|||
|
|
delay(500);
|
|||
|
|
SERIAL_PORT_MONITOR.println("01");
|
|||
|
|
#ifdef CAN_2518FD
|
|||
|
|
CAN.mcpDigitalWrite(GPIO_PIN_0, GPIO_LOW);
|
|||
|
|
CAN.mcpDigitalWrite(GPIO_PIN_1, GPIO_HIGH);
|
|||
|
|
#else
|
|||
|
|
CAN.mcpDigitalWrite(MCP_RX0BF, LOW);
|
|||
|
|
CAN.mcpDigitalWrite(MCP_RX1BF, HIGH);
|
|||
|
|
#endif
|
|||
|
|
delay(500);
|
|||
|
|
}
|
|||
|
|
|
|||
|
|
/*********************************************************************************************************
|
|||
|
|
END FILE
|
|||
|
|
*********************************************************************************************************/
|